Skip to content
Menu

Industries

Explosion protection for flour, feed and grain plants

In flour, feed and grain plants, dust is part of normal production. Explosion protection therefore looks at the inside of the equipment, the dust collection system and housekeeping together, along the whole line from grain intake to bagging.

Where the explosion risk comes from

Flour, grain dust, bran, starch and feed dust can explode when they form a cloud of sufficient concentration in air. Inside silos, elevators, filters and pneumatic lines such a cloud is part of normal operation. Outside the equipment the main hazard is the dust layer: a small explosion inside can lift the layer into the air and cause a second, much larger explosion through the building.

Sources of release

  • Grain intake pits and unloading
  • Silos and bins
  • Bucket elevators
  • Chain and screw conveyors
  • Roller mills and sifters
  • Dust filters and cyclones
  • Pneumatic conveying
  • Bagging and bulk loading
  • Feed pellet presses and dryers

For how zones are calculated and drawn, see hazardous area classification. For plants in the United States, see dust hazard analysis support.

What we look at closely

The bucket elevator is one of the most critical items in a flour or feed mill. It holds a dust cloud in normal operation, and mechanical ignition sources such as belt slip, friction and hot bearings are inside it. We therefore check belt slip and alignment monitoring, bearing temperature monitoring, and explosion venting or isolation separately for each elevator.

How we assess it

  1. Dust properties. Explosion data for the products and intermediates are taken from published data or test reports. The finest fraction, the filter dust, is assessed separately.
  2. Sources along the line. From intake to bagging, the inside and outside of each item of equipment are assessed, together with the points where dust escapes and how often it escapes.
  3. Housekeeping and layers. Where and how fast dust settles is established on site, or from photographs and cleaning records. The cleaning regime and the permitted layer are tied to the zone decision.
  4. Ignition sources. Mechanical friction, hot bearings, tramp metal in the raw material, static electricity, hot equipment such as dryers and pellet presses, and hot work are assessed.
  5. Protective measures. The need for explosion venting, suppression and isolation is identified for silos, elevators and filters. Sizing these systems is a separate design task.

Gaps worth checking

  • Only the silo assessed, with elevators, filters and pneumatic lines left out.
  • Belt slip and alignment monitoring missing on elevators, or bypassed.
  • Magnets that remove tramp metal from the raw material not maintained.
  • Dust settled on beams, ducts and the tops of equipment.
  • Cleaning with compressed air, which raises a dust cloud.
  • Filter dust treated as if it were the main product, although the finest dust is often the easiest to ignite.
  • Fire risk at dryers and pellet presses kept apart from the dust assessment.

What we need from you

  • Process flow diagram and layout
  • Technical data for silos, elevators and filters
  • Safety data sheets or dust test reports for the products
  • Documents for explosion vents and isolation systems
  • Housekeeping instructions and records
  • Ex certificates of the equipment

What you receive

Dust zone drawings for the whole line from intake to bagging, and a check of equipment temperature limits against the dust. With them come a control plan for housekeeping and dust layers, the protective measures needed, an action plan and area rules.

Rules in your country

  • Great Britain. The assessment is a DSEAR risk assessment. Dust zones 20, 21 and 22 follow Schedule 2 of DSEAR and are usually classified to BS EN 60079-10-2.
  • Germany. The dust zones are documented in the Explosionsschutzdokument (§ 6(9) GefStoffV), with the technical rules of the TRGS 720 series.
  • Netherlands. The zones go into the explosieveiligheidsdocument as part of the RI&E; dust zoning normally follows NPR 7910-2.
  • United States. Grain handling facilities fall under OSHA 29 CFR 1910.272, and combustible dust is assessed in a dust hazard analysis under NFPA 660 (formerly NFPA 652). As a subcontractor to consulting firms, we prepare the desk part of the analysis and, on request, Class II Division drawings to NFPA 499; your qualified person leads and signs.
  • Türkiye. The zones go into the explosion protection document required by the 2013 regulation, and we work on site.

Questions

Our plant is new and the equipment carries the CE and Ex marking. Do we still need an assessment?

Yes. The CE and Ex marking concern the design of the product. The zones, the housekeeping and the suitability of the equipment for each zone are the employer's assessment under the workplace rules: Directive 1999/92/EC in the EU, DSEAR in Great Britain.

Our silos have explosion vents. Is that enough?

Venting is an important protective measure. Whether it is enough depends on the silo and the dust, the size of the vent and where it discharges. Isolation, which stops an explosion travelling into connected equipment such as an elevator or a filter, is assessed separately.

Do we need dust testing?

Not always. Published data are often adequate for flour, grain and feed dusts. Testing is recommended where the result is sensitive to these values or the product is unusual.

This page is general information. The result for your site is set by calculations based on your site data.

Send us your documents

Within one working day of receiving them we send our first observations and a fixed-price offer. Every question, answer and assumption goes into the project file, so the document can be checked line by line.

Based in
Istanbul, Türkiye
First reply
Usually within one working day